Welcome Overseas

Aluminium 5083 is known for exceptional performance in extreme environments. 5083 is highly resistant to attack by both seawater and industrial chemical environments.
Alloy 5083 also retains exceptional strength after welding. It has the highest strength of the non-heat treatable alloys but is not recommended for use in temperatures in excess of 65°C.

Applications:
Alloy 5083 is typically used in:

• Shipbuilding
• Rail cars
• Vehicle bodies
• Tip truck bodies
• Mine skips and cages
• Pressure vessels

Mechanical Properties shown are for H32 temper

• Alloy Designations
• Alloy 5083 also confirms to:
• GM41
• A95083
• AlMG4.5Mn
• Al Mg4.5 Mn0.7

Temper Types:
The most common tempers for 5083 aluminium are:

• O - Soft
• H111 - Some work hardening imparted by shaping processes but less than required for H11 temper
• H32 - Work hardened by rolling then stabilised by low-temperature heat treatment to quarter hard

Supplied Forms:

• Plate
• Sheet

Weldability:

• When welding 5083 to itself or another alloy from the same sub-group, the recommended filler metal is 5183. Other suitable fillers are 5356 and 5556.

 

We are leading exporter of Aluminum Alloy Rod 6061 T6.

General characteristics and uses:

• Excellent joining characteristics, good acceptance of applied coatings. Combines relatively high strength, good workability, and high resistance to corrosion; widely available.

Applications:

• Aircraft fittings, camera lens mounts, couplings, marines fittings and hardware, electrical fittings and connectors, decorative or misc. hardware, hinge pins, magneto parts, brake pistons, hydraulic pistons, appliance fittings, valves and valve parts.

6082 Aluminum Alloy Rods Description

 

 

Overview

 

6082 Aluminum Alloy Rods are high-strength, corrosion-resistant aluminum alloy rods, widely used in structural applications. They offer excellent mechanical properties, weldability, and machinability.

 

 

Chemical Composition

 

- Aluminum (95.5-98.5%)

- Magnesium (0.6-1.2%)

- Silicon (0.7-1.3%)

- Manganese (0.4-1.0%)

- Iron (0.5%)

- Copper (0.1%)

- Zinc (0.2%)

- Titanium (0.1%)

 

 

Mechanical Properties

 

- Tensile Strength: 55,000 psi (380 MPa)

- Yield Strength: 50,000 psi (345 MPa)

- Elongation at Break: 10%

- Hardness: 100-120 HB

- Density: 0.0975 lb/in³ (2.7 g/cm³)

 

 

Key Features

 

- High strength-to-weight ratio

- Excellent corrosion resistance

- Good weldability and machinability

- High thermal conductivity

- Resistance to stress corrosion cracking

 

 

Applications

 

- Aerospace

- Automotive

- Marine hardware

- Sports equipment

- Construction

- Machinery

- Shipbuilding

- Railway

 

 

Forms Available

 

- Rods (diameter: 1/4" to 12")

- Bars (thickness: 1/4" to 4")

- Plates (thickness: 1/4" to 4")

- Sheets (thickness: 0.025" to 0.25")

 

 

Temper Designations

 

- T6: Heat-treated and artificially aged

- T4: Heat-treated and naturally aged

- O: Annealed

 

 

Certifications

 

- ASTM B221

- AMS 4160

- 

Aluminum Alloy Rods Grades Details:

• Aluminum Alloy Rods Grades 6061 T6 .
• Aluminum Alloy Rods Grades 2024 T3 .
• Aluminum Alloy Rods Grades 7075 T6 .
• Aluminum Alloy Rods Grades 2011 T3 .
• Aluminum Alloy Rods Grades 5086 .
• Aluminum Alloy 
• Aluminum Alloy Rods Grades 2014 .
• Rods Grades 6082 .
• Aluminum Alloy Rods Grades 5251 .
• Aluminum Alloy Rods Grades 1050 .

T6 7075 Aluminum Alloy Rods Description

Overview
T6 7075 Aluminum Alloy Rods are high-strength, aerospace-grade aluminum alloy rods, known for their exceptional mechanical properties, corrosion resistance, and durability.

Chemical Composition
- Aluminum (87.1-91.4%)- Zinc (5.1-6.1%)- Magnesium (2.1-2.9%)- Copper (1.2-2.0%)- Chromium (0.18-0.28%)- Iron (0.5%)- Silicon (0.4%)- Manganese (0.3%)

Mechanical Properties
- Tensile Strength: 83,000 psi (572 MPa)- Yield Strength: 73,000 psi (503 MPa)- Elongation at Break: 6-8%- Hardness: 150-180 HB- Density: 0.0975 lb/in³ (2.7 g/cm³)

Key Features
- High strength-to-weight ratio- Excellent corrosion resistance- Good weldability and machinability- High thermal conductivity- Resistance to stress corrosion cracking

Applications
- Aerospace- Aircraft structures- Defense- Automotive racing- High-performance sports equipment- Marine hardware

Forms Available
- Rods (diameter: 1/4" to 12")- Bars (thickness: 1/4" to 4")- Plates (thickness: 1/4" to 4")- Sheets (thickness: 0.025" to 0.25")

Temper Designations
- T6: Heat-treated and artificially aged- T4: Heat-treated and naturally aged- O: Annealed

Certifications
- ASTM B221- AMS 4124- ASME SB221- EN 573-3- ISO 6361

Packaging and Pricing
- Wrapped in plastic or paper- Packed in wooden boxes or crates- Custom packaging available- Price Range: ₹1,200 - ₹12,000 (dependent on size, quantity, and supplier)

Alternative Alloys
- 6061 T6- 6082 T6- 2024 T3- 7075 T73 (corrosion-resistant variant)

Precautions
- Handle with care to avoid scratches and damage- Store in dry, well-ventilated areas- Follow safety guidelines for machining and welding

Typical Fabrication Methods
- Machining (CNC, milling, turning)- Welding (MIG, TIG, FCAW)- Cutting (sawing, shearing)- Forming (bending, extrusion)

Benefits
- High strength-to-weight ratio- Excellent corrosion resistance- Good weldability and machinability- High thermal conductivity- Resistance to stress corrosion cracking

Comparison with 6061
- Higher strength and hardness- Similar corrosion resistance- Better machinability- Lower ductility

Note: Properties and applications may vary depending on the specific temper and form. Consult the manufacturer or supplier for specific information.
T6 Temper Benefits
- Improved strength and hardness- Enhanced corrosion resistance- Better stability at high temperatures- Improved weldability
Caution
- 7075 T6 alloy is prone to stress corrosion cracking in marine environments.- Use 7075 T73 variant for improved corrosion resistance.

5251 Aluminium Alloy Rods contains nominally 2.0% magnesium & 0.30% manganese. It has good workability, medium static strength, high fatigue strength, good weldability, and very good corrosion resistance, especially in marine atmospheres. It also has the low density and excellent thermal conductivity common to all aluminium alloys. It is commonly used in sheet, plate and tube form.
Machinability
5251 is readily machinable by conventional methods. It should be machined at high speed with copious lubrication to avoid thermal distortion of the workpiece. Sharp tools are essential. High speed steel or tungsten carbide may be used. Cuts should be deep and continuous, with high cutting speeds. Woodworking machinery may be suitable for short runs.
Welding
5251 is readily weldable by standard techniques. It is frequently welded with GTAW (TIG) or GMAW (MIG). Aluminium must be very dry & clean to avoid contamination & porosity of the weld. Filler metals 1100, 4043 or 4047 are used. 4043 is the most crack tolerant. Shielding gas must be dry & free of hydrogen.

Heat Treatment
Aluminium 5251 is annealed at 345°C, time at temperature and cooling rate are unimportant. Stress relief is rarely required, but can be carried out at about 220°C. If loss of strength is of concern, stress relief tests should be conducted

2014 Aluminum Alloy Bars Description

Overview
2014 Aluminum Alloy Bars are high-strength, aerospace-grade aluminum alloy bars, known for their exceptional mechanical properties, corrosion resistance, and durability.

Chemical Composition
- Aluminum (93.5-95.5%)- Copper (3.5-4.5%)- Silicon (0.5-1.2%)- Iron (0.5%)- Manganese (0.4-1.2%)- Magnesium (0.2-0.8%)- Zinc (0.2%)- Titanium (0.1%)

Mechanical Properties
- Tensile Strength: 70,000-80,000 psi (483-552 MPa)- Yield Strength: 60,000-70,000 psi (414-483 MPa)- Elongation at Break: 10-15%- Hardness: 120-150 HB- Density: 0.0975 lb/in³ (2.7 g/cm³)

Key Features
- High strength-to-weight ratio- Excellent corrosion resistance- Good weldability and machinability- High thermal conductivity- Resistance to stress corrosion cracking

Applications
- Aerospace- Aircraft structures- Defense- Automotive racing- High-performance sports equipment- Machine building

Forms Available
- Bars (thickness: 1/4" to 4")- Rods (diameter: 1/4" to 12")- Plates (thickness: 1/4" to 4")- Sheets (thickness: 0.025" to 0.25")

Temper Designations
- T6: Heat-treated and artificially aged- T4: Heat-treated and naturally aged- O: Annealed

Certifications
- ASTM B211- AMS 4133- ASME SB211- EN 573-3- ISO 6361

Packaging and Pricing
- Wrapped in plastic or paper- Packed in wooden boxes or crates- Custom packaging available- Price Range: ₹900 - ₹9,000 (dependent on size, quantity, and supplier)

Alternative Alloys
- 2024 T3- 6061 T6- 6082 T6- 7075 T6

Precautions
- Handle with care to avoid scratches and damage- Store in dry, well-ventilated areas- Follow safety guidelines for machining and welding

Typical Fabrication Methods
- Machining (CNC, milling, turning)- Welding (MIG, TIG, FCAW)- Cutting (sawing, shearing)- Forming (bending, extrusion)

Benefits
- High strength-to-weight ratio- Excellent corrosion resistance- Good weldability and machinability- High thermal conductivity- Resistance to stress corrosion cracking

Comparison with 6061
- Higher strength and hardness- Similar corrosion resistance- Better machinability- Lower ductility

Note: Properties and applications may vary depending on the specific temper and form. Consult the manufacturer or supplier for specific information.

T6 Temper Benefits
- Improved strength and hardness- Enhanced corrosion resistance- Better stability at high temperatures- Improved weldability

5086 Aluminum Alloy Rods has very good corrosion resistance (susceptible to deterioration after prolonged exposure to elevated temperatures) and moderate strength. Its weldability is a plus. It is used similarly to aluminum 5083 (although 5086 has better stress corrosion cracking resistance) - in transportation, pressure vessels, cryogenics, towers and drilling rigs, gas/oil piping, ordnance, and armor plate.

5083 Aluminium Alloy Bars has very good corrosion resistance (susceptible to deterioration after prolonged exposure to elevated temperatures) and moderate strength. Its weldability is a plus. It is used in transportation, pressure vessels, cryogenics, towers and drilling rigs, gas/oil piping, ordnance, and armor plate.

10mm Aluminium Alloy Bars contains nominally 2.0% magnesium & 0.30% manganese. It has good workability, medium static strength, high fatigue strength, good weldability, and very good corrosion resistance, especially in marine atmospheres. It also has the low density and excellent thermal conductivity common to all aluminium alloys. It is commonly used in sheet, plate and tube form. Machinability5251 is readily machinable by conventional methods. It should be machined at high speed with copious lubrication to avoid thermal distortion of the workpiece. Sharp tools are essential. High speed steel or tungsten carbide may be used. Cuts should be deep and continuous, with high cutting speeds. Woodworking machinery may be suitable for short runs.

We are involved in offering a wide range of all products to our most valued clients.Our range of all products is widely appreciated by our clients which are situated all round the nation.We offer our range of products at most affordable prices. Also availaible in large quantity as per customer demand.

5083 Aluminium Alloy Bars  : Good machinability, especially free-cutting qualities, good mechanical properties. Excellent surface finish capability.

Uses: Adapters, carburetor parts, clock parts and gears, knobs, camera parts, meter shafts and gears, nozzles, pencil and pen parts, oil line filters, pipe stems and filters, radio parts, screwdriver caps, spindles, telephone parts, TV fittings, tripod fittings, machine parts, hose parts, pipe stems.

6m Aluminium Alloy Rods  One of the most widely used aluminum alloys, it finds applications in a variety of structural areas such as aircraft structures, fasteners, hardware, wheels, screw machine products. 2024 exhibits poor corrosion resistance for an aluminum alloy.

6061 Aluminium Alloy Rods: Good machinability, especially free-cutting qualities, good mechanical properties. Excellent surface finish capability.

Uses: Adapters, carburetor parts, clock parts and gears, knobs, camera parts, meter shafts and gears, nozzles, pencil and pen parts, oil line filters, pipe stems and filters, radio parts, screwdriver caps, spindles, telephone parts, TV fittings, tripod fittings, machine parts, hose parts, pipe stems.

Aluminum Alloy Rods 5086 has very good corrosion resistance (susceptible to deterioration after prolonged exposure to elevated temperatures) and moderate strength. Its weldability is a plus. It is used similarly to aluminum 5083 (although 5086 has better stress corrosion cracking resistance) - in transportation, pressure vessels, cryogenics, towers and drilling rigs, gas/oil piping, ordnance, and armor plate.

General 6061 characteristics and uses: Excellent joining characteristics, good acceptance of applied coatings. Combines relatively high strength, good workability, and high resistance to corrosion; widely available.

Uses: Aircraft fittings, camera lens mounts, couplings, marines fittings and hardware, electrical fittings and connectors, decorative or misc. hardware, hinge pins, magneto parts, brake pistons, hydraulic pistons, appliance fittings, valves and valve parts.

Round Aluminium Alloy Bars 
 Excellent joining characteristics, good acceptance of applied coatings. Combines relatively high strength, good workability, and high resistance to corrosion; widely available.

Use Aircraft fittings, camera lens mounts, couplings, marines fittings and hardware, electrical fittings and connectors, decorative or misc. hardware, hinge pins, magneto parts, brake pistons, hydraulic pistons, appliance fittings, valves and valve parts.

2024-T3 This is the most common of the high-strength alloys. Aircraft quality, 2024 T3 aluminum sheet is thought of as the aircraft alloy because of its strength. It has excellent fatigue resistance. Welding is generally not recommended. Typical uses for 2024-T3 alclad aluminum sheet are aircraft skins, cowls, aircraft structures, and also for RV repair and restoration like Airstreams because of it's shiny finish (2024T3 alclad)

3003-H14 is most widely used of aluminum alloys, pure aluminum with manganese added for strength, approx 20% stronger than the 1000 series alloys. 3003-H14 aluminum sheet has great workability and may be deep drawn, spun, welded or brazed. 3003 aluminum sheet is NON-heat treatable. This aluminum sheet is widely used for general purposes.

Aluminium Sheet comes in many different alloys and thicknesses for different types of applications. Any aluminium under 3/16" thickness is generally referred to as "Sheet". Aluminium Plate is produced in thicknesses from 3/16" and up and in several different alloys, each with their specific qualities. Choose a thickness to view what alloys we have in stock for that size plate. We stock 3003H14 but we will special order any alloy and any thickness up to 6" thick. Aluminium Supply will also custom cut to size any sheet or plate to meet your requirements.

Aluminium Alloy Sheet Description

Overview
Aluminium Alloy Sheets are flat, rolled products made from various aluminium alloys, offering excellent corrosion resistance, durability, and lightweight properties.

Materials
- 1000 series (pure aluminium)- 2000 series (copper-aluminium)- 3000 series (manganese-aluminium)- 5000 series (magnesium-aluminium)- 6000 series (magnesium-silicon-aluminium)- 7000 series (zinc-aluminium)

Alloy Specifications
- 6061 T6- 6063 T5- 6082 T6- 7075 T6- 2024 T3

Dimensions
- Thickness: 0.025" to 4" (0.6 mm to 101.6 mm)- Width: 12" to 120" (304.8 mm to 3048 mm)- Length: 24" to 480" (609.6 mm to 12192 mm)

Key Features
- Corrosion-resistant- High strength-to-weight ratio- Good weldability and machinability- High thermal conductivity- Resistance to stress corrosion cracking

Applications
- Aerospace- Automotive- Construction- Marine hardware- Furniture- Decorative trim- Industrial equipment

Temper Designations
- T6: Heat-treated and artificially aged- T4: Heat-treated and naturally aged- O: Annealed

Certifications
- ASTM B209- AMS 4045- ASME SB209- EN 573-3- ISO 6361

Packaging and Pricing
- Wrapped in plastic or paper- Packed in wooden boxes or crates- Custom packaging available- Price Range: ₹500 - ₹5,000 (dependent on size, quantity, and supplier)

Alternative Materials
- Stainless steel- Carbon steel- Copper- PVC

Precautions
- Handle with care to avoid scratches and damage- Store in dry, well-ventilated areas- Follow safety guidelines for machining and welding

Typical Fabrication Methods
- Cutting (sawing, shearing)- Machining (CNC, milling, turning)- Welding (MIG, TIG, FCAW)- Forming (bending, extrusion)

Benefits
- Corrosion-resistant- High strength-to-weight ratio- Good weldability and machinability- High thermal conductivity- Resistance to stress corrosion cracking

Mechanical Properties
- Tensile strength: 10,000-80,000 psi (69-552 MPa)- Yield strength: 5,000-70,000 psi (34-483 MPa)- Elongation at break: 5-20%

Thermal Properties
- Thermal conductivity: 100-240 W/mK- Thermal expansion coefficient: 20-25 μm/mK

Note: Properties and applications may vary depending on the specific alloy and temper. Consult the manufacturer or supplier for specific information.

Aluminium alloy 5251 is a medium strength alloy possessing good ductility and therefore good formability. Alloy 5251 is known for work hardening rapidly and is readily weldable. It also possesses high corrosion resistance particularly in marine environments.

Applications:
5251 is typically used in:

• Boats
• Panelling and pressings
• Marine structures
• Aircraft parts
• Vehicle panels
• Furniture tubing
• Silos
• Containers

Mechanical Properties shown are for H24 condition - Mechanical properties for other tempers are shown on page 2.

Alloy Designations

• Alloy 5251 also confirms to:
• Al Mg2
• Al 2.0Mg 0.3Mn

Temper Types:
The most common tempers for 5252 aluminium are:

• H24 - Work hardened by rolling then annealed to half hard
• H26 - Work hardened by rolling then annealed to three-quarter hard
• O - Soft
• H22 - Work hardened by rolling then annealed to quarter hard

Supplied Forms

• Plate
• Sheet

Alloy 2024 plate products are used in fuselage structurals, wing tension members, shear webs and ribs and structural areas where stiffness, fatigue performance and good strength are required. Sheet products, usually alclad, are used extensively in commercial and military aircraft for fuselage skins, wing skins and engine areas where elevated temperatures to 250°F (121°C) are often encountered.

Chemical Composition Limits (WT.%)

• Si - 0.50
• Fe - 0.50
• Cu - 3.8-4.9
• Mn - 0.30-0.9
• Mg - 1.2-1.8
• Cr. - 0.10
• Zn - 0.25
• Ti - 0.15
• Others, each - 0.05
• Others, total - 0.15
• Balance, Aluminum

Description:

• Alloy 2024 was introduced by Swagat steel and alloys in 1985 as an alclad sheet in the T3 temper. It was the first Al-Cu-Mg alloy to have a yield strength approaching 50,000-psi and generally replaced 2017-T4 (Duralumin) as the predominant 2XXX series aircraft alloy. With its relatively good fatigue resistance, especially in thick plate forms, aluminum alloy 2024 continues to be specified for many aerospace structural applications. 2024 varient alloys, such as higher purity 2124 and 2324, with improvements in strength and other specific characteristics, have also found application in critical aircraft structures. An improved sheet alloy for fuselage applications was introduced in 1991. Alclad C188 offers improved fracture toughness and fatigue crack growth while maintaining the strength characteristics of 2024.
• Aluminium Alloy 2024 is available in bare and alclad sheet and plate product forms in the annealed state and several tempers of T3, T4, and T8 types

7075 Aluminum Alloy Plate Description

Overview
7075 Aluminum Alloy Plates are high-strength, aerospace-grade aluminum alloy plates, known for their exceptional mechanical properties, corrosion resistance, and durability.

Alloy Composition
- Aluminum (87.1-91.4%)- Zinc (5.1-6.1%)- Magnesium (2.1-2.9%)- Copper (1.2-2.0%)- Chromium (0.18-0.28%)- Iron (0.5%)- Silicon (0.4%)- Manganese (0.3%)

Mechanical Properties
- Tensile Strength: 83,000 psi (572 MPa)- Yield Strength: 73,000 psi (503 MPa)- Elongation at Break: 6-8%- Hardness: 150-180 HB- Density: 0.0975 lb/in³ (2.7 g/cm³)

Dimensions
- Thickness: 0.125" to 4" (3.18 mm to 101.6 mm)- Width: 12" to 120" (304.8 mm to 3048 mm)- Length: 24" to 480" (609.6 mm to 12192 mm)

Key Features
- High strength-to-weight ratio- Excellent corrosion resistance- Good weldability and machinability- High thermal conductivity- Resistance to stress corrosion cracking

Applications
- Aerospace- Aircraft structures- Defense- Automotive racing- High-performance sports equipment- Machine building

Temper Designations
- T6: Heat-treated and artificially aged- T4: Heat-treated and naturally aged- O: Annealed

Certifications
- ASTM B209- AMS 4045- ASME SB209- EN 573-3- ISO 6361

Packaging and Pricing
- Wrapped in plastic or paper- Packed in wooden boxes or crates- Custom packaging available- Price Range: ₹1,500 - ₹15,000 (dependent on size, quantity, and supplier)

Alternative Alloys
- 6061 T6- 6082 T6- 2024 T3- 7075 T73 (corrosion-resistant variant)

Precautions
- Handle with care to avoid scratches and damage- Store in dry, well-ventilated areas- Follow safety guidelines for machining and welding

Typical Fabrication Methods
- Machining (CNC, milling, turning)- Welding (MIG, TIG, FCAW)- Cutting (sawing, shearing)- Forming (bending, extrusion)

Benefits
- High strength-to-weight ratio- Excellent corrosion resistance- Good weldability and machinability- High thermal conductivity- Resistance to stress corrosion cracking

Thermal Properties
- Thermal conductivity: 130 W/mK- Thermal expansion coefficient: 23 μm/mK

Surface Finishes
- Mill finish- Anodized- Powder coated- Polished

Tolerances
- Thickness: ±0.005"- Width: ±1/8"- Length: ±1/8"

Note: Properties and applications may vary depending on the specific temper and form. Consult the manufacturer or supplier for specific information.

Aluminium alloy 1050 is a popular grade of aluminium for general sheet metal work where moderate strength is required.
Alloy 1050 is known for its excellent corrosion resistance, high ductility and highly reflective finish.

Applications - Alloy 1050 is typically used for:

• Chemical process plant equipment
• Food industry containers
• Pyrotechnic powder
• Architectural flashings
• Lamp reflectors
• Cable sheathing

Alloy Designations:

• Aluminium alloy 1050 also corresponds to the following

Standard designations and specifications:

• AA1050A
• S1B
• A91050

Temper Types

• The most common tempers for 1050 aluminium are:
• O - Soft

Supplied Forms:

• Plain sheet
  Plain sheet with a PVC coating on one side
  Stucco sheet
  Stucco sheet with a PVC coating on one side Shate

Weldability:

• When welding 1050 to itself or an alloy from the same subgroup the recommended filler wire is 1100. For welding to alloys 5083 and 5086 or alloys from the 7XXX series, the recommend wire is 5356. For other alloys use 4043 filler wire.

Blue 6061 Aluminium Alloy Sheet  is available to the client in good quality and at reasonable market price.

Available Sizes

• Blue 6061 Aluminium Alloy Sheet is available in 0.5mm and 200 mm.

Characteristics:

• Aluminium Alloy Sheet is a heat-treatable grade widely used in structural applications. The alloy has good corrosion resistance and welds ability and possesses good formability in certain Tempers.

Typical Applications

• Blue 6061 Aluminium Alloy Sheet is used in structural areas where both strength and corrosion resistance is required, truck bodies and frames, and towers.

Window Aluminum Profile Description

Overview
Window Aluminum Profiles are extruded aluminum sections used for fabricating windows, doors, and other architectural applications, offering durability, corrosion resistance, and low maintenance.

Materials
- 6063 T5- 6061 T6- 6082 T6

Dimensions
- Customizable to specific requirements- Standard sizes:    - 25mm to 150mm (1" to 6")    - 30mm to 200mm (1.2" to 7.9")

Key Features
- Corrosion-resistant- High strength-to-weight ratio- Good thermal insulation- Weather-tight seals- Low maintenance- Anodized or powder-coated finishes

Applications
- Windows (sliding, casement, awning)- Doors (sliding, swinging)- Curtain walls- Facades- Roofing- Partition systems

Profile Types
- I-beam- T-slot- H-shaped- U-shaped- Custom profiles

Surface Finishes
- Anodized (clear, bronze, black)- Powder-coated (various colors)- Mill finish- Electrostatic powder coating

Certifications
- ASTM B221- AMS 4133- ASME SB221- EN 573-3- ISO 6361

Packaging and Pricing
- Wrapped in plastic or paper- Packed in wooden boxes or crates- Custom packaging available- Price Range: ₹500 - ₹5,000 (dependent on size, quantity, and supplier)

Alternative Materials
- PVC- Steel- Wood- Fiberglass

Precautions
- Handle with care to avoid scratches and damage- Store in dry, well-ventilated areas- Follow safety guidelines for fabrication and installation

Typical Fabrication Methods
- Extrusion- Cutting (sawing, shearing)- Drilling- Machining (CNC, milling, turning)- Welding (MIG, TIG, FCAW)

Benefits
- Corrosion-resistant- High strength-to-weight ratio- Good thermal insulation- Weather-tight seals- Low maintenance

Thermal Properties
- Thermal conductivity: 160 W/mK- Thermal expansion coefficient: 23 μm/mK

Mechanical Properties
- Tensile strength: 40,000 psi (276 MPa)- Yield strength: 30,000 psi (207 MPa)- Elongation at break: 12%

Note: Properties and applications may vary depending on the specific alloy and temper. Consult the manufacturer or supplier for specific information.

We Are Expert In AllWelcome Overseas WorksWelcome Overseas Industries, is engaged in manufacturing of Stainless Steel Welded Pipes, Seamless Pipe and EFW Pipe and the requirements of many large and medium scale industries from all over the globe qualitatively.Our specialties include :Stainless Steel 304, 304L, 316, 316L, 316TI, 309S, 310, 321, 409M, 410, 420, 431, 904L. Aluminium Sheets 1100, 8011, 6082, 5052, Aluminium Structural 6063, 6351, 6101, 6061, Aluminium Tubes IPS Grade 6101 grades in form of Rod, Sheets/Plates , Bolt and Nut , Wire, Pipe (ERW & SEAMLESS) and Pipe Fittings : Flanges, Bends, Elbows, Reducers, Stubends, and also Carbon Steel/ Mild Steel Sheets / Plates, C.S. Pipes Seamless / Erw Pipes and Pipe Fittings. We also stock large quantities of Non-Ferrous Metals: Copper, Brass, Aluminum, Titanium, Monel, Inconel, Nickel, Bronze, Super Duplex, Tin, Lead, in all forms like rods, sheets, wires, profiles, extrusions, tubes, foils, coils, Etc.

We are leading exporter of 6061 T6 Aluminum Alloy Rod.

Size 3mm to 300mm

General characteristics and uses:

• Excellent joining characteristics, good acceptance of applied coatings. Combines relatively high strength, good workability, and high resistance to corrosion; widely available.

Applications:

• Aircraft fittings, camera lens mounts, couplings, marines fittings and hardware, electrical fittings and connectors, decorative or misc. hardware, hinge pins, magneto parts, brake pistons, hydraulic pistons, appliance fittings, valves and valve parts.

2024 T3 Aluminum Alloy Rods One of the most widely used aluminum alloys, it finds applications in a variety of structural areas such as aircraft structures, fasteners, hardware, wheels, screw machine products. 2024 exhibits poor corrosion resistance for an aluminum alloy.

Aluminium Alloy 6m Bars
characteristics and uses: Excellent joining characteristics, good acceptance of applied coatings. Combines relatively high strength, good workability, and high resistance to corrosion; widely available.

Use Aircraft fittings, camera lens mounts, couplings, marines fittings and hardware, electrical fittings and connectors, decorative or misc. hardware, hinge pins, magneto parts, brake pistons, hydraulic pistons, appliance fittings, valves and valve parts.

Aluminium alloy 5251 contains nominally 2.0% magnesium & 0.30% manganese. It has good workability, medium static strength, high fatigue strength, good weldability, and very good corrosion resistance, especially in marine atmospheres. It also has the low density and excellent thermal conductivity common to all aluminium alloys. It is commonly used in sheet, plate and tube form.

Machinability5251 is readily machinable by conventional methods. It should be machined at high speed with copious lubrication to avoid thermal distortion of the workpiece. Sharp tools are essential. High speed steel or tungsten carbide may be used. Cuts should be deep and continuous, with high cutting speeds. Woodworking machinery may be suitable for short runs.
Welding5251 is readily weldable by standard techniques. It is frequently welded with GTAW (TIG) or GMAW (MIG). Aluminium must be very dry & clean to avoid contamination & porosity of the weld. Filler metals 1100, 4043 or 4047 are used. 4043 is the most crack tolerant. Shielding gas must be dry & free of hydrogen.

Heat TreatmentAluminium 5251 is annealed at 345°C, time at temperature and cooling rate are unimportant. Stress relief is rarely required, but can be carried out at about 220°C. If loss of strength is of concern, stress relief tests should be conducted.

Aluminium 5086 Alloy Rods  has very good corrosion resistance (susceptible to deterioration after prolonged exposure to elevated temperatures) and moderate strength. Its weldability is a plus. It is used similarly to aluminum 5083 (although 5086 has better stress corrosion cracking resistance) - in transportation, pressure vessels, cryogenics, towers and drilling rigs, gas/oil piping, ordnance, and armor plate.

Aluminium Alloy Rods 7075 T6: Very high strength material used for highly stressed structural parts.

Applications: Aircraft fittings, gears and shafts, fuse parts, meter shafts and gears, missile parts, regulating valve parts, worm gears, keys, aircraft, aerospace and defense applications; bike frames, all terrain vehicle (ATV) sprockets.

Featured Products:

• 5083 Aluminium Alloy – Supplied in sheet marine grade tempers H116, H321, H323; to spec ASTM B928. Tempers O, H112, H32; to spec ASTM B209, and extrusion shapes in various tempers and specifications. This is an excellent marine environment corrosion resistant aluminum alloy, commonly used in Europe and Asia but becoming more frequently used in North America. It is primarily an alloy used for its corrosion resistant properties as it is especially good on inter granular corrosion resistance. Also, the tensile and yield strength is higher than 5086 alloy, so often these properties too are used by designers for their aluminum vessels. This alloy also has good welding capabilities for fabricating vessels. 5083 is also in inventory as H32 temper which is a good standard engineering alloy, but it does not have the corrosion resistance of the other special marine tempers.
• 5086 Aluminium Alloy – Supplied in marine grade tempers H116, H321; to spec ASTM B928. Tempers O, H112, H32; to spec ASTM B209, and extrusion shapes in various tempers and specifications. This is an excellent marine environment corrosion resistant aluminum alloy, most commonly used in North America. It is also a marine grade alloy used for its corrosion resistant properties as it is also very good on inter granular corrosion. The benefits this alloy brings over standard alloys such as 5052 or 6061 is the corrosion resistance and better welding capabilities and good forming properties. 5086 is also in inventory as H32 temper which is a good standard engineering alloy, but it does not have the corrosion resistance of the other special marine tempers.
• 5456 Aluminium Alloy – This alloy is primarily used in areas where high strength and better welding parameters are required in a marine vessel or other engineering applications. Alloy 5456 is stocked in tempers H116, H321; to spec ASTM B928. Tempers O, H112, H32; to spec ASTM B209 this alloy has higher tensile strength than other marine alloys such as 5083 or 5086, and good corrosion resistance in a sea water environment, but not always the formability and corrosion performance of some of the other alloys.
• 5454 Aluminium Alloy – This alloy is primarily used in areas where good formability is required, it is used in O, H112, H32, H34; to specification ASTM B209 Tempers and is an excellent choice for large pressure vessels and certain marine fabricated products. The formability is at its best in the soft 0 temper, but also sometimes used in H32 or H34 tempers too. However the strength and corrosion resistance are not always as good as other alloys, so as always a marine structural engineer should be consulted for each application.
• 5052 H32 – Sheet & plate – A common alloy with good strength and weldability and it is easy to form and fabricate. However, not always considered a true marine alloy.
• 6061 T6 Sheet & plate – A heat treated alloy with higher strength used in many general engineering applications. However, again not considered a true marine alloy.

3mm Aluminium Pipe Description:

Material: Aluminium (Alloy 6061, 6063, or 6082)

Outer Diameter: 3mm (0.118 in)

Wall Thickness: 0.5mm (0.02 in) to 1mm (0.039 in)

Length: 6 meters (19.7 ft) standard, customizable up to 12 meters (39.37 ft)

Surface Finish:

- Anodized- Powder coated- Mill finish- Polished

Features:
- Lightweight- Corrosion-resistant- High strength-to-weight ratio- Excellent thermal conductivity- Non-magnetic- Resistant to corrosion in marine environments

Applications:
- Aerospace- Automotive- HVAC systems- Refrigeration- Electrical conduits- Pneumatic systems- Medical equipment- Food processing

Specifications:
- ASTM B210 (Aluminum and Aluminum-Alloy Drawn Seamless Tubes)- EN 573 (Aluminum and Aluminum Alloys)- JIS H4040 (Aluminum Alloy Pipes and Tubes)

Tolerances:
- Outer diameter: ±0.1mm (0.004 in)- Wall thickness: ±0.05mm (0.002 in)- Length: ±10mm (0.39 in)

Packing and Shipping:
- Wrapped in plastic or paper- Packed in bundles or on pallets- Shipped via truck, sea, or air freight

Certifications:
- ISO 9001- PED (Pressure Equipment Directive)- CE marking- Material test reports (MTRs)

Physical Properties:
- Density: 2.7 g/cm³- Melting point: 660°C (1220°F)- Tensile strength: 290-310 MPa (42-45 ksi)- Yield strength: 240-260 MPa (35-38 ksi)

Chemical Composition:
- Aluminum (Al): 97-99%- Magnesium (Mg): 0.8-1.2%- Silicon (Si): 0.4-0.8%- Copper (Cu): 0.1-0.3%- Other elements (zinc, titanium, etc.)

The 3mm aluminium pipe offers excellent strength, corrosion resistance, and lightweight properties, making it suitable for various industrial applications.

Aluminum Alloy 5083 contains 5.2% magnesium, 0.1% manganese and 0.1% chromium. In the tempered condition, it is strong, and retains good formability due to excellent ductility. 5083 has high resistance to corrosion, and is used in marine applications. It has the low density and excellent thermal conductivity common to all Aluminum alloys.

Typical Applications:

• Require a weldable alloy of high to moderate strength, with good corrosion resistance. Marine applications, unfired welded pressure vessels, TV towers, drilling rigs, transportation equipment, armour plate.

Description:

• Aluminum 5083 is a strong magnesium-manganese-chromium-Aluminum alloy. It can be hardened by cold work, but is not heat treatable to higher strength. It has good ductility for the strength level, better than most other 5000 series alloys (see figure).

Corrosion Resistance:

• Alloy 5083 has excellent resistance to general corrosion, and is used in marine applications. Resistance is excellent in aqueous solutions in the pH range 4 – 9. The corrosion resistance of Aluminum alloys relies on a protective surface oxide film, which when damaged is readily repaired by the rapid reaction between Aluminum and oxygen. However, the high reactivity of the base metal can give rapid corrosion if the film cannot be repaired, so Aluminum alloys are not suitable for use with reducing media. Alloy 5083 can be anodised to improve the corrosion resistance by thickening the protective surface film. Alloy 5083 can be susceptible to exfoliation corrosion in severe applications. Material in the H116 temper is least susceptible, and passes the ASTM G66 Exfoliation Susceptibility Test (ASSET Test). AS 1734 suggests alloy 5083 should not be used above 65°C.

Pressure Vessels:

• AS1210 Pressure Vessels pre-qualifies alloy 5083 for pressure service for temperatures up to 65°C in the O, H112 & H321 tempers.

2014 T651 Aluminium Alloy Sheet Description

 

 

Overview

 

2014 T651 Aluminium Alloy Sheets are high-strength, aerospace-grade aluminium alloy sheets, known for their exceptional mechanical properties, corrosion resistance, and durability.

 

 

Alloy Composition

 

- Aluminium (93.5-95.5%)

- Copper (3.5-4.5%)

- Silicon (0.5-1.2%)

- Iron (0.5%)

- Manganese (0.4-1.2%)

- Magnesium (0.2-0.8%)

- Zinc (0.2%)

- Titanium (0.1%)

 

 

Mechanical Properties

 

- Tensile Strength: 70,000-80,000 psi (483-552 MPa)

- Yield Strength: 60,000-70,000 psi (414-483 MPa)

- Elongation at Break: 10-15%

- Hardness: 120-150 HB

- Density: 0.0975 lb/in³ (2.7 g/cm³)

 

 

Dimensions

 

- Thickness: 0.025" to 4" (0.6 mm to 101.6 mm)

- Width: 12" to 120" (304.8 mm to 3048 mm)

- Length: 24" to 480" (609.6 mm to 12192 mm)

 

 

Key Features

 

- High strength-to-weight ratio

- Excellent corrosion resistance

- Good weldability and machinability

- High thermal conductivity

- Resistance to stress corrosion cracking

 

 

Applications

 

- Aerospace

- Aircraft structures

- Defense

- Automotive racing

- High-performance sports equipment

- Machine building

 

 

Temper Designation

 

- T651: Heat-treated, stress-relieved, and artificially aged

 

 

Certifications

 

- ASTM B209

- AMS 4133

- ASME SB209

- EN 573-3

- ISO 6361

 

 

Packaging and Pricing

 

- Wrapped in plastic or paper

- Packed in wooden boxes or crates

- Custom packaging available

- Price Range: ₹1,500 - ₹15,000 (dependent on size, quantity, and supplier)

 

 

Alternative Alloys

 

- 6061 T6

- 6082 T6

- 7075 T6

- 2024 T3

 

 

Precautions

 

- Handle with care to avoid scratches and damage

- Store in dry, well-ventilated areas

- Follow safety guidelines for machining and welding

 

 

Typical Fabrication Methods

 

- Machining (CNC, milling, turning)

- Welding (MIG, TIG, FCAW)

- Cutting (sawing, shearing)

- Forming (bending, extrusion)

 

 

Benefits

 

- High strength-to-weight ratio

- Excellent corrosion resistance

- Good weldability and machinability

- High thermal conductivity

- Resistance to stress corrosion cracking

 

 

Thermal Properties

 

- Thermal conductivity: 120 W/mK

- Thermal expansion coefficient: 22 μm/mK

 

 

Note: Properties and applications may vary depending on the specific temper and form. Consult the manufacturer or supplier for specific information.

Bare Aluminium Strip:
A versatile and widely used material, Bare Aluminium Strip is a popular choice for various applications.
Key Features:
- Made from high-quality aluminium alloy (1050, 1060, 1100, 3003, etc.)- Thickness options: 0.1mm to 6.0mm- Width options: 10mm to 1500mm- Length options: coils or cut-to-length- Free from coatings, oils, and lubricants- High corrosion resistance- Excellent conductivity and thermal properties- Durable and lightweight
Applications:
- Electrical and electronics- Construction and building- Transportation (automotive, aerospace)- Packaging and consumer goods- Industrial and machinery
Benefits:
- High strength-to-weight ratio- Excellent corrosion resistance- Good conductivity and thermal properties- Versatile and widely available- Can be easily formed, cut, and machined
Bare Aluminium Strip is a popular choice for various applications due to its unique combination of properties. Its high corrosion resistance, excellent conductivity, and durability make it an ideal material for industries such as electrical, construction, and transportation.

Coated Aluminium Strip:
A high-quality, corrosion-resistant aluminium strip with a protective coating, offering excellent durability and versatility for various industrial applications.
Description:
- Material: Aluminium (1050, 1060, 1070, 1100, or 3003)- Form: Strip- Thickness: [Insert thickness range]- Width: [Insert width range]- Length: [Insert length range]- Coating: [Insert coating type, e.g. polyester, polyvinylidene fluoride (PVDF), or silicone]
Features:
- High corrosion resistance- Good weldability and machinability- Resistance to stress corrosion cracking- Good electrical and thermal conductivity- Lightweight and durable- Coating provides additional protection against corrosion and wear
Applications:
- Electrical and electronics industry- Automotive industry- Construction and building materials- Packaging industry- Marine hardware and equipment- Decorative and architectural applications
Specifications:
- Composition: 99.5% Aluminium (1050), 99.6% Aluminium (1060), 99.7% Aluminium (1070), 99.0% Aluminium (1100), or 96.5% Aluminium (3003)- Melting point: 660°C (1220°F)- Density: 2.7 g/cm³- Tensile strength: 70-170 MPa (10-25 ksi)- Corrosion resistance: Excellent in marine environments- Coating thickness: [Insert coating thickness range]
Dimensions:
- Thickness tolerances: +/- 0.1mm- Width tolerances: +/- 0.5mm- Length tolerances: +/- 10mm- Straightness: 1mm/m max
Certifications:
- ASTM B209- ASME SB209- ISO 6363- DIN 1725
Packaging:
- Strips are packaged in wooden or plastic coils- Coils are wrapped in protective paper or plastic- Strips are secured with wire or plastic ties

Aluminium Flat Bars:

 

A lightweight, corrosion-resistant flat bar, offering excellent durability and versatility for various industrial applications.

 

Description:

 

- Material: Aluminium (6061, 6063, or 6082)

- Form: Flat Bar

- Thickness: [Insert thickness range]

- Width: [Insert width range]

- Length: [Insert length range]

 

Features:

 

- Lightweight and corrosion-resistant

- High strength-to-weight ratio

- Good weldability and machinability

- Resistance to stress corrosion cracking

- Good electrical and thermal conductivity

 

Applications:

 

- Aerospace and defense

- Automotive industry

- Construction and building materials

- Electrical and electronics industry

- Marine hardware and equipment

 

Specifications:

 

- Composition: 97% Aluminium, 1% Magnesium, 0.6% Silicon (6061)

- Melting point: 660°C (1220°F)

- Density: 2.7 g/cm³

- Tensile strength: 240-300 MPa (35-45 ksi)

- Corrosion resistance: Good in marine environments

 

Dimensions:

 

- Thickness tolerances: +/- 0.1mm

- Width tolerances: +/- 0.5mm

- Length tolerances: +/- 10mm

- Straightness: 1mm/m max

 

Certifications:

 

- ASTM B221

- ASME SB221

- ISO 6363

- DIN 1725

 

Packaging:

 

- Flat bars are packaged in wooden or plastic bundles

- Bundles are wrapped in protective paper or plastic

- Flat bars are secured with wire or plastic ties

We Are Expert In AllWelcome Overseas WorksWelcome Overseas Industries, is engaged in manufacturing of Stainless Steel Welded Pipes, Seamless Pipe and EFW Pipe and the requirements of many large and medium scale industries from all over the globe qualitatively.Our specialties include :Stainless Steel 304, 304L, 316, 316L, 316TI, 309S, 310, 321, 409M, 410, 420, 431, 904L. Aluminium Sheets 1100, 8011, 6082, 5052, Aluminium Structural 6063, 6351, 6101, 6061, Aluminium Tubes IPS Grade 6101 grades in form of Rod, Sheets/Plates , Bolt and Nut , Wire, Pipe (ERW & SEAMLESS) and Pipe Fittings : Flanges, Bends, Elbows, Reducers, Stubends, and also Carbon Steel/ Mild Steel Sheets / Plates, C.S. Pipes Seamless / Erw Pipes and Pipe Fittings. We also stock large quantities of Non-Ferrous Metals: Copper, Brass, Aluminum, Titanium, Monel, Inconel, Nickel, Bronze, Super Duplex, Tin, Lead, in all forms like rods, sheets, wires, profiles, extrusions, tubes, foils, coils, Etc.